Request a quote

Paper tube, core, cone, fibre drum or composite can: which do you need?

All five are wound from paper in plies. What they carry, and how they fail, is what separates them.

Corrugation floor with kraft reels, paper tubes stacked against the wall and corrugated sheets

Choose by what goes on or in the product. A paper tube carries a heavy reel of paper, film or foil. A winding core carries yarn, thread, technical textiles or metal coil. A textile cone is a tapered core shaped to a yarn winder. A fibre drum holds dry bulk powders, granules and solids. A composite can holds smaller quantities of dry product for retail or gift packs. All five are made the same basic way, by winding paper in plies with adhesive and curing it, so the differences are in shape, wall, ends and what the specification has to say.

The five compared

Wound paper products compared
ProductCarriesKey dimensionsStrength stated asEnds or closure
Paper tubePaper, board, film and foil reels; label stockID, wall, length; ovality and straightnessFlat or radial crush from reel weightPlain, notched or capped
Winding coreMetal coil, yarn, thread, technical textilesID, OD, length with tolerancesCrush from wound weight and tension; axial if stood on endPlain, notched or capped
Textile coneYarn on a winderTaper, length, base diameterConstruction agreed; test on requestSurface and colour code
Fibre drumDry powders, granules, solidsCapacity, diameter, heightStacking requirementLid and locking type; liner if needed
Composite canDry products, gift and retail packsDiameter and heightSet by product and handlingPaper, metal or plastic ends; inner liner

Tube or core?

The terms overlap. A core is usually the centre on which film, paper, yarn or metal coil is wound; a tube often means a longer or heavier-walled section, such as the tubes on which paper mills wind finished reels. Both are specified the same way: inner diameter, wall thickness or outer diameter, and length, each with a tolerance, plus the crush strength or the reel weight and winding tension. As a rule, a small increase in wall thickness raises crush resistance steeply, while a larger inner diameter at the same wall lowers it sharply. See core crush strength and wall thickness.

When a core becomes a cone

A cone is a core with a taper, made to seat on a particular yarn winder. Fit matters more than strength: the taper, length and base diameter must match the cone holder, and the surface must give the yarn enough grip. If yarn is steamed or conditioned on the cone, the construction has to be agreed for that.

When the wound tube becomes a container

Close one end and a wound tube becomes a fibre drum or a composite can. The questions change from crush and fit to closure, barrier and contents. Fibre drums are for dry materials only; a liner does not turn one into a liquid container. Composite cans can take paper, metal or plastic ends and an inner liner. In both cases the wound body is not intended for direct food contact, so food use depends on a liner and a declaration for that use.

Spiral or parallel winding

In a spiral wound core the plies run at an angle along the mandrel, which suits continuous production in long lengths. In a parallel or convolute core they wrap straight around, a method often used for heavy-duty cores. Ask which construction suits your strength and length requirement.

One weakness they share

Paper takes up moisture from humid air and loses strength. Cores can crush under reel weight in a damp warehouse, drums can deform when stacked, and a damp tube swells and changes its chuck fit. Say how the product will be stored and moved, and keep stock dry, wrapped and off the floor.

What to send

  • What is wound on it or packed in it, and the weight
  • The machine it runs on, or a drawing or sample
  • Dimensions with tolerances, or capacity
  • Strength requirement, ends or closure, liner
  • Storage conditions, reuse or single-trip, annual volume

Bollant winds all five from recycled paper made at its own mills, with adhesive from its own adhesives unit, to your drawing. Send the details through request a quote.

Questions buyers ask

What is the difference between a paper core and a paper tube?

The terms overlap. A core is the centre on which film, yarn or coil is wound; a tube usually means a longer or heavier-walled section, such as the tubes paper mills wind reels on. Both are specified by ID, wall, length and crush strength.

Is a textile cone just a tapered core?

In construction, yes. In use, fit and surface matter most: taper, length and base diameter must match the winder, and the surface must grip the yarn.

Can a fibre drum hold liquids?

No. Fibre drums are built for dry powders, granules and solids, and a liner does not make them suitable for liquids.

Which wound paper products can be used for food?

The wound body is not intended for direct food contact. Fibre drums and composite cans carry food only with a liner or construction covered by a declaration for that use.

Why do wound paper products fail in the monsoon?

Paper absorbs moisture and loses strength. Specify for humid storage and keep stock dry, wrapped and off the floor.

Bollant Industries · Published 2026-11-21

Company footage · silent

Paper web on the machine

Send us your specification

Send the parameters you have. We confirm what we can make, the values we can agree in writing and the documents that go with them.